Cars, Trucks, Boats, RV's, Transmissions, A/C Units, Even Guns and More.
Cerma Treatment is the only product of it's kind
Cerma’s “1 TIME" Engine treatment will restore new car performance and savings for years to come!
* Need your car to last longer? Cerma can help you with that.
* Need your car to perform better? Cerma can help with that.
* Need better MPG? Cerma can help with that.
* Need better lubrication that protects your investment for years to come? Cerma can help with that!
Protects New ---- Revives old.
Restores Engine and Transmission Performance
Restores Horsepower & Torque
Restores Compression
Extends oil change intervals by 2-3 times (see oil reports)
Active STM-3® with Carbon Guard
Restores Fuel Economy* 4.2 to 21 % as Tested
Reduces Emission Gases (92% EPA certified Test)
Reduced maintenance, increased equipment life
Cleans Carbon Deposits within your engine
Reduced Engine Vibration and Noise (Harmonics)
Stops cold start problems. (Tested to -40 Deg.)
Lowers Operating Temperatures
Seals and Protects Metal Parts from Wear & Deposits
Does not contain PTFE or Chlorinated Paraffin.
Cerma is 100% active ingredients.
Cerma is 100% Organic.
All Cerma Products are Fully Insured (US & Foreign) .Notice: All information stated above is based on 10 years of Real Data, and not Hype or dreams of a marketing group. Cerma Guarantee's IT!
Turn your worn out motor into a high performance ceramic Engine!
Cerma STM-3 is a unique engine treatment that is added to the oil of a hot engine and over a short period of time it penetrates all the metal parts within with a hard glossy ceramic (Silicon Carbide – Sic) finish. It re-seals the engine from within restoring lost compression and any imbalance between the cylinders.
Silicon Carbide is high strength, high hardness and has amazing thermal conductivity. It considerably reduces noise and vibration (harmonics) and puts an end to ‘dry starts’ – two of the leading causes of engine wear.
Cerma is not an oil treatment; it’s an advanced metal treatment process. It’s so effective, that after only 20 miles of driving you’ll notice how much smoother and quieter the engine is running, Cerma is ‘sub-micron’ so it even penetrates the varnish build-up and adheres to all the engine parts, filling in all the micro pitting in the metal with a hard polished permanent layer of 2 to 6 microns. Cerma significantly reduces heat and friction and this will be apparent in improved fuel economy and engineperformance. In tests, Cerma has proven capable of withstanding pressures in excess of 350,000 psi and lubricating at temperatures above 1900 F. The treatment continues improving for up to 90 days and one application is good for 200,000 miles.
Cerma is not just for engines, it can be used anywhere metal meets metal and needs lubrication. (Electric motors, gear boxes, drive trains, hydraulics, etc.) Cerma considerably extends the lifespan of the fleet, saving on maintenance costs and on the capital expenditure for replacement. It has had its mostremarkable results with engines that are burning oil and/or losing compression. Some users report that routine maintenance cycles are now down to 1 in every 3 Tests in EPA certified labs have shown an astounding 92% reduction in harmful emission gases.
Cerma – Technical Details: Normal oils avoid hot metal at approximately 275° F and will oxidize (break down) at approximately 375°-450° F. In contrast STM-3 treated oil will seal and protect metal that the oil comes in contact with and deposits a 2-6 micron sub-surface of Silicon Carbide. Cerma also significantlyreduces temperatures by absorbing engine heat,thereby insulating the oil and helping it to retain its lubricity for longer. The remaining stm-3 treated oil is attracted to the hot metal and will not allow the oil to oxidize until 500–640 deg. F.
Cerma Treatment Procedure:
Cerma must be administered as detailed below or it will not work as designed.Follow instructions carefully for best results. It is important to heat up the engine to a normal operating temperature, before adding cerma with the engine running, simply add Cerma through the oil filler cap.
Increase the Vehicle’s RPM’s above 2000for about 10 minutes then drive for at least 1/2 hour. (Do Not shut off the engine within that time period)..
* Need your car to last longer? Cerma can help you with that.
* Need your car to perform better? Cerma can help with that.
* Need better MPG? Cerma can help with that.
* Need better lubrication that protects your investment for years to come? Cerma can help with that!
Protects New ---- Revives old.
Restores Engine and Transmission Performance
Restores Horsepower & Torque
Restores Compression
Extends oil change intervals by 2-3 times (see oil reports)
Active STM-3® with Carbon Guard
Restores Fuel Economy* 4.2 to 21 % as Tested
Reduces Emission Gases (92% EPA certified Test)
Reduced maintenance, increased equipment life
Cleans Carbon Deposits within your engine
Reduced Engine Vibration and Noise (Harmonics)
Stops cold start problems. (Tested to -40 Deg.)
Lowers Operating Temperatures
Seals and Protects Metal Parts from Wear & Deposits
Does not contain PTFE or Chlorinated Paraffin.
Cerma is 100% active ingredients.
Cerma is 100% Organic.
All Cerma Products are Fully Insured (US & Foreign) .Notice: All information stated above is based on 10 years of Real Data, and not Hype or dreams of a marketing group. Cerma Guarantee's IT!
Turn your worn out motor into a high performance ceramic Engine!
Cerma STM-3 is a unique engine treatment that is added to the oil of a hot engine and over a short period of time it penetrates all the metal parts within with a hard glossy ceramic (Silicon Carbide – Sic) finish. It re-seals the engine from within restoring lost compression and any imbalance between the cylinders.
Silicon Carbide is high strength, high hardness and has amazing thermal conductivity. It considerably reduces noise and vibration (harmonics) and puts an end to ‘dry starts’ – two of the leading causes of engine wear.
Cerma is not an oil treatment; it’s an advanced metal treatment process. It’s so effective, that after only 20 miles of driving you’ll notice how much smoother and quieter the engine is running, Cerma is ‘sub-micron’ so it even penetrates the varnish build-up and adheres to all the engine parts, filling in all the micro pitting in the metal with a hard polished permanent layer of 2 to 6 microns. Cerma significantly reduces heat and friction and this will be apparent in improved fuel economy and engineperformance. In tests, Cerma has proven capable of withstanding pressures in excess of 350,000 psi and lubricating at temperatures above 1900 F. The treatment continues improving for up to 90 days and one application is good for 200,000 miles.
Cerma is not just for engines, it can be used anywhere metal meets metal and needs lubrication. (Electric motors, gear boxes, drive trains, hydraulics, etc.) Cerma considerably extends the lifespan of the fleet, saving on maintenance costs and on the capital expenditure for replacement. It has had its mostremarkable results with engines that are burning oil and/or losing compression. Some users report that routine maintenance cycles are now down to 1 in every 3 Tests in EPA certified labs have shown an astounding 92% reduction in harmful emission gases.
Cerma – Technical Details: Normal oils avoid hot metal at approximately 275° F and will oxidize (break down) at approximately 375°-450° F. In contrast STM-3 treated oil will seal and protect metal that the oil comes in contact with and deposits a 2-6 micron sub-surface of Silicon Carbide. Cerma also significantlyreduces temperatures by absorbing engine heat,thereby insulating the oil and helping it to retain its lubricity for longer. The remaining stm-3 treated oil is attracted to the hot metal and will not allow the oil to oxidize until 500–640 deg. F.
Cerma Treatment Procedure:
Cerma must be administered as detailed below or it will not work as designed.Follow instructions carefully for best results. It is important to heat up the engine to a normal operating temperature, before adding cerma with the engine running, simply add Cerma through the oil filler cap.
Increase the Vehicle’s RPM’s above 2000for about 10 minutes then drive for at least 1/2 hour. (Do Not shut off the engine within that time period)..